The impact of low-mode symmetry on inertial fusion energy output in the burning plasma state.

Indirect Drive Inertial Confinement Fusion Experiments on the National Ignition Facility (NIF) have achieved a burning plasma state with neutron yields exceeding 170 kJ, roughly 3 times the prior record and a necessary stage for igniting plasmas. The results are achieved despite multiple sources of degradations that lead to high variability in performance. Results shown here, for the first time, include an empirical correction factor for mode-2 asymmetry in the burning plasma regime in addition to previously determined corrections for radiative mix and mode-1. Analysis shows that including these three corrections alone accounts for the measured fusion performance variability in the two highest performing experimental campaigns on the NIF to within error. Here we quantify the performance sensitivity to mode-2 symmetry in the burning plasma regime and apply the results, in the form of an empirical correction to a 1D performance model. Furthermore, we find the sensitivity to mode-2 determined through a series of integrated 2D radiation hydrodynamic simulations to be consistent with the experimentally determined sensitivity only when including alpha-heating.

Observations and properties of the first laboratory fusion experiment to exceed a target gain of unity.

An indirect-drive inertial fusion experiment on the National Ignition Facility was driven using 2.05 MJ of laser light at a wavelength of 351 nm and produced 3.1±0.16 MJ of total fusion yield, producing a target gain G=1.5±0.1 exceeding unity for the first time in a laboratory experiment [Phys. Rev. E 109, 025204 (2024)10.1103/PhysRevE.109.025204]. Herein we describe the experimental evidence for the increased drive on the capsule using additional laser energy and control over known degradation mechanisms, which are critical to achieving high performance. Improved fuel compression relative to previous megajoule-yield experiments is observed. Novel signatures of the ignition and burn propagation to high yield can now be studied in the laboratory for the first time.

Increased Ion Temperature and Neutron Yield Observed in Magnetized Indirectly Driven D_{2}-Filled Capsule Implosions on the National Ignition Facility.

The application of an external 26 Tesla axial magnetic field to a D_{2} gas-filled capsule indirectly driven on the National Ignition Facility is observed to increase the ion temperature by 40% and the neutron yield by a factor of 3.2 in a hot spot with areal density and temperature approaching what is required for fusion ignition [1]. The improvements are determined from energy spectral measurements of the 2.45 MeV neutrons from the D(d,n)^{3}He reaction, and the compressed central core B field is estimated to be ∼4.9 kT using the 14.1 MeV secondary neutrons from the D(T,n)^{4}He reactions. The experiments use a 30 kV pulsed-power system to deliver a ∼3 µs current pulse to a solenoidal coil wrapped around a novel high-electrical-resistivity AuTa_{4} hohlraum. Radiation magnetohydrodynamic simulations are consistent with the experiment.

Experimental achievement and signatures of ignition at the National Ignition Facility.

An inertial fusion implosion on the National Ignition Facility, conducted on August 8, 2021 (N210808), recently produced more than a megajoule of fusion yield and passed Lawson's criterion for ignition [Phys. Rev. Lett. 129, 075001 (2022)10.1103/PhysRevLett.129.075001]. We describe the experimental improvements that enabled N210808 and present the first experimental measurements from an igniting plasma in the laboratory. Ignition metrics like the product of hot-spot energy and pressure squared, in the absence of self-heating, increased by ∼35%, leading to record values and an enhancement from previous experiments in the hot-spot energy (∼3×), pressure (∼2×), and mass (∼2×). These results are consistent with self-heating dominating other power balance terms. The burn rate increases by an order of magnitude after peak compression, and the hot-spot conditions show clear evidence for burn propagation into the dense fuel surrounding the hot spot. These novel dynamics and thermodynamic properties have never been observed on prior inertial fusion experiments.

Design of an inertial fusion experiment exceeding the Lawson criterion for ignition.

We present the design of the first igniting fusion plasma in the laboratory by Lawson's criterion that produced 1.37 MJ of fusion energy, Hybrid-E experiment N210808 (August 8, 2021) [Phys. Rev. Lett. 129, 075001 (2022)10.1103/PhysRevLett.129.075001]. This design uses the indirect drive inertial confinement fusion approach to heat and compress a central "hot spot" of deuterium-tritium (DT) fuel using a surrounding dense DT fuel piston. Ignition occurs when the heating from absorption of α particles created in the fusion process overcomes the loss mechanisms in the system for a duration of time. This letter describes key design changes which enabled a ∼3-6× increase in an ignition figure of merit (generalized Lawson criterion) [Phys. Plasmas 28, 022704 (2021)1070-664X10.1063/5.0035583, Phys. Plasmas 25, 122704 (2018)1070-664X10.1063/1.5049595]) and an eightfold increase in fusion energy output compared to predecessor experiments. We present simulations of the hot-spot conditions for experiment N210808 that show fundamentally different behavior compared to predecessor experiments and simulated metrics that are consistent with N210808 reaching for the first time in the laboratory "ignition."

Burning plasma achieved in inertial fusion.

Obtaining a burning plasma is a critical step towards self-sustaining fusion energy1. A burning plasma is one in which the fusion reactions themselves are the primary source of heating in the plasma, which is necessary to sustain and propagate the burn, enabling high energy gain. After decades of fusion research, here we achieve a burning-plasma state in the laboratory. These experiments were conducted at the US National Ignition Facility, a laser facility delivering up to 1.9 megajoules of energy in pulses with peak powers up to 500 terawatts. We use the lasers to generate X-rays in a radiation cavity to indirectly drive a fuel-containing capsule via the X-ray ablation pressure, which results in the implosion process compressing and heating the fuel via mechanical work. The burning-plasma state was created using a strategy to increase the spatial scale of the capsule2,3 through two different implosion concepts4-7. These experiments show fusion self-heating in excess of the mechanical work injected into the implosions, satisfying several burning-plasma metrics3,8. Additionally, we describe a subset of experiments that appear to have crossed the static self-heating boundary, where fusion heating surpasses the energy losses from radiation and conduction. These results provide an opportunity to study α-particle-dominated plasmas and burning-plasma physics in the laboratory.

Foam-lined hohlraum, inertial confinement fusion experiments on the National Ignition Facility.

Experiments on the National Ignition Facility (NIF) to study hohlraums lined with a 20-mg/cc 400-µm-thick Ta_{2}O_{5} aerogel at full scale (hohlraum diameter = 6.72 mm) are reported. Driven with a 1.6-MJ, 450-TW laser pulse, the performance of the foam liner is diagnosed using implosion hot-spot symmetry measurements of the high-density carbon (HDC) capsule and measurement of inner beam propagation through a thin-wall 8-µm Au window in the hohlraum. Results show an improved capsule performance due to laser energy deposition further inside the hohlraum, leading to a modest increase in x-ray drive and reduced preheat due to changes in the x-ray spectrum when the foam liner is included. In addition, the outer cone bubble uniformity is improved, but the predicted improvement in inner beam propagation to improve symmetry control is not realized for this foam thickness and density.

Time-Resolved Fuel Density Profiles of the Stagnation Phase of Indirect-Drive Inertial Confinement Implosions.

The implosion efficiency in inertial confinement fusion depends on the degree of stagnated fuel compression, density uniformity, sphericity, and minimum residual kinetic energy achieved. Compton scattering-mediated 50-200 keV x-ray radiographs of indirect-drive cryogenic implosions at the National Ignition Facility capture the dynamic evolution of the fuel as it goes through peak compression, revealing low-mode 3D nonuniformities and thicker fuel with lower peak density than simulated. By differencing two radiographs taken at different times during the same implosion, we also measure the residual kinetic energy not transferred to the hot spot and quantify its impact on the implosion performance.

Measurement of high-pressure shock waves in cryogenic deuterium-tritium ice layered capsule implosions on NIF.

The first measurements of multiple, high-pressure shock waves in cryogenic deuterium-tritium (DT) ice layered capsule implosions on the National Ignition Facility have been performed. The strength and relative timing of these shocks must be adjusted to very high precision in order to keep the DT fuel entropy low and compressibility high. All previous measurements of shock timing in inertial confinement fusion implosions [T. R. Boehly et al., Phys. Rev. Lett. 106, 195005 (2011), H. F. Robey et al., Phys. Rev. Lett. 108, 215004 (2012)] have been performed in surrogate targets, where the solid DT ice shell and central DT gas regions were replaced with a continuous liquid deuterium (D2) fill. This report presents the first experimental validation of the assumptions underlying this surrogate technique.

Precision shock tuning on the national ignition facility.

Ignition implosions on the National Ignition Facility [J. D. Lindl et al., Phys. Plasmas 11, 339 (2004)] are underway with the goal of compressing deuterium-tritium fuel to a sufficiently high areal density (ρR) to sustain a self-propagating burn wave required for fusion power gain greater than unity. These implosions are driven with a very carefully tailored sequence of four shock waves that must be timed to very high precision to keep the fuel entropy and adiabat low and ρR high. The first series of precision tuning experiments on the National Ignition Facility, which use optical diagnostics to directly measure the strength and timing of all four shocks inside a hohlraum-driven, cryogenic liquid-deuterium-filled capsule interior have now been performed. The results of these experiments are presented demonstrating a significant decrease in adiabat over previously untuned implosions. The impact of the improved shock timing is confirmed in related deuterium-tritium layered capsule implosions, which show the highest fuel compression (ρR~1.0 g/cm(2)) measured to date, exceeding the previous record [V. Goncharov et al., Phys. Rev. Lett. 104, 165001 (2010)] by more than a factor of 3. The experiments also clearly reveal an issue with the 4th shock velocity, which is observed to be 20% slower than predictions from numerical simulation.

Demonstration of ignition radiation temperatures in indirect-drive inertial confinement fusion hohlraums.

We demonstrate the hohlraum radiation temperature and symmetry required for ignition-scale inertial confinement fusion capsule implosions. Cryogenic gas-filled hohlraums with 2.2 mm-diameter capsules are heated with unprecedented laser energies of 1.2 MJ delivered by 192 ultraviolet laser beams on the National Ignition Facility. Laser backscatter measurements show that these hohlraums absorb 87% to 91% of the incident laser power resulting in peak radiation temperatures of T(RAD)=300 eV and a symmetric implosion to a 100 µm diameter hot core.

Surgery for thyroid goiter in western India. A prospective analysis of 334 cases.

334 consecutive cases of thyroid swellings operated by a single surgical unit over 9 years have been analysed prospectively. There was a female preponderence (4.39:1). The swellings were clinically differentiated into uninodular (39.52%), multinodular (47.31%) and diffuse (13.17%). Hyperthyroidism was manifested in 49 cases (14.67%). Pressure symptoms were present in only 1.5% cases. FNAC detected malignancy in 14 of 162 cases (8.64%). The initial 100 cases were operated upon by standard Lahey's technique and the latter 234 by modified technique described by Bapat et al for benign thyroid disease. Operations performed included nodulectomies (5.39%), hemithyroidectomies (41.92%), partial thyroidectomies (25.75%), subtotal (25.45%) and near total thyroidectomies (1.5%). Post-operative complications were higher in the first group and included unilateral cord palsies-5 (5%). hypocalcemia-4 (4%) hypoparathyroidism-1 (1%) haemorrhage-1 (1%) and mortality-1 (1%) vis a vis cord palsies-2 (0.85%), hypocalcemia-3 (1.28%), hypoparathyroidism-1 (0.43%) and there was no mortality. Histopathology revealed 83 (24.85%) colloid goiters, 193 (57.78%) nodular goiters, 21 (6.29%) follicular adenomas, 7 (2.10%) cases of thyroiditis and 30 (8.98%) malignancies. This study reveals the lower incidence of RLN palsy after modified thyroidectomies, and a low incidence of malignancy.

Menstrual irregularities and lactation failure may precede thyroid dysfunction or goitre.

Menstrual and reproductive history of 178 women referred to the thyroid clinic was compared with 49 healthy controls. Cases were classified as euthyroid, hypothyroid or hyperthyroid after clinical examination and after serum T3, T4, TSH measurements. Reproductive history was related chronologically to symptoms and signs of thyroid dysfunction. Only 31.8% of hypothyroid and 35.3% of hyperthyroid women had normal menstrual pattern in contrast with 56.3% of Euthyroid and 87.8% of healthy controls (p < 0.001). Reproductive failure (infertility, pregnancy wastage, failure of lactation) occurred in 37.5% of hypothyroid and 36.5% of hyperthyroid cases against 16.3% of euthyroid and 16.7% of healthy controls (p < 0.05). Interestingly, in 45% of cases with menstrual abnormality, the anomaly was antecedent to other clinical features by a variable period of two months to ten years. Reproductive failure and lactation failure also preceded thyroid dysfunction or goitre. Reproductive dysfunction may therefore be considered as one of the presenting symptoms of thyroid disorders in women, keeping in mind both menstrual irregularities and lactation failure may also arise from other common or idiopathic origins. Especially in women with menstrual irregularities in the perimenopausal age if thyroid dysfunction is detected, pharmacotherapy may be a superior alternative to surgical interventions like hysterectomy.

Analysis of 105 uninodular goitres.

Data on 105 solitary thyroid nodules, confirmed at surgery to be solitary, is presented. Six (5.7%) were malignant, 4 papillary and 2 follicular. The sensitivity and the specificity of 131I radionuclide thyroid scan (n = 90) were 100% and 24% respectively. Similarly, the sensitivity and specificity of fine needle aspiration cytology (n = 65) was 75% and 100% respectively. In both instances, the "gold standard" was the histopathology of the surgically removed nodule. In order to avoid unnecessary surgery, without missing malignancy, we would recommend the combination of radionuclide thyroid scan and FNAC for investigation of solitary thyroid nodules.

Antipyrine and doxycycline pharmacokinetics in patients with thyroid disorders.

Pathological conditions are known to affect pharmacokinetics of many drugs. Antipyrine half-life is used as a marker of liver microsomal enzyme function. Antipyrine pharmacokinetics, therefore, was investigated in 23 thyrotoxic and 11 euthyroid goitre patients. Of these, 11 thyrotoxic and 9 euthyroid goitre patients also participated in doxycycline bioavailability studies. In thyrotoxic patients, antipyrine half-life and AUCo infinity and doxycycline Cpmax and AUCo infinity were found to be reduced as compared to those of healthy euthyroid normal subjects. Following treatment of thyrotoxicosis, the antipyrine half-life and AUCo infinity returned to normal. Doxycycline AUCo infinity returned to near normal range but Cpmax did not.